Netonix WISP Gigabito POE šakotuvas (WS-26-500-DC)
„Netonix WISP“ konfigūruojamas Gigabito POE šakotuvas WS-26-500-DC, 24 Gigabito POE jungtys su srovės jutikliais, 2 SFP nukreipimo jungtys, nuo 9 V iki 72 V kintamos galios įvestis, 500 W išvestis, energija airFIBER, „airmax“ radijas
Managed Passive POE Switch
The Netonix® WISP Switch™ model WS-26-500-DC is designed specifically for the WISP industry with a rugged chassis and extended operating temperature range. It features a simple yet powerful user interface providing the software features WISPs need in a switch.
500 Watt SMART DC power supply accepts 9V to 72V DC variable input while providing uninterrupted 24V and 48V POE
If you have a 48V-54V power supply you should use the WS-26-DC unit.
(24) Gbps POE Ports
(2) SFP Uplink Ports
Optional 19” rack mount kit / Din Rail kit (RMK-26)
WARNING: This switch is not designed to operate on negative 48V site, using -48V DC will damage the switch as it does not have isolated input output power.
The WISP Switch™ features the ability to power many popular 24V, 48V/50V passive PoE devices from many manufacturers including the Ubiquiti Networks® airMAX™, UniFi™, SAF™, MIMOSA™, Ligowav™, and airFIBER™ product lines.
Monitor DC voltage and current into the switch from your batteries.
Monitors the DC power supply temperature with auto and programmable thermal shutdown.
Program the switch to shut down lower priority POE ports when batteries get low and to restore them when sufficient reserves return or when it detects charging has resumed from solar or wind.
If power gets too low it can be configured to shut down all POE ports and hibernate your remote site until it detects solar or wind charging has resumed and sufficient reserves are generated.
You can chose to run your batteries all the way down to 9V to keep the tower up or have it shut down in stages to preserve your energy.
Since we designed the power supply to have its own micro processor and to communicate to the switch itself we have full control over the power supply and all relative telemetry generated by sensors built into the power supply.
• LAG – Port aggregation LACP/Static
• STP / RSTP / MSTP (MSTP available with firmware v2.0)
• Port mirroring and remote monitoring via Wire Shark with CPSP
• VLAN dot1Q/QinQ/Port Trunking
• SNMP - complete statistical reporting
• SMTP alerts - configurable
• Bandwidth limiting per port
• Ping watch dog per port
• Scheduled port bouncing
• Cable Diagnostics
• Loop Protection
• DHCP Snooping
• IGMP Snooping
• Flow Control - with back pressure
• Storm Control
• Multicast Filtering
• Port Isolation
• Auto TFTP Backup on Config Change
• UDP - Ubiquiti Discovery Protocol
• CDP - Cisco Discovery Protocol
• Security - access control list and login tarpit
Manufactured and Assembled North America
Standard 19” rack mount / Desktop / Wall mount: YES
Dimensions: 343mm x 248 mm x 44mm
Weight: 3,1 kg
Power Input: 9-72 VDC
Chassis Earth Ground Lug: YES
Max. Power Consumption: N/A
Intelligent Forced Air Cooling With Fan RPM Monitoring: YES
Switch Core and PHYs: Vitesse
Processor: MIPS 24K 416 MHz
System Memory: 128 MB
Flash Storage: 16 MB
Total Non-Blocking Line Rate: 10 Gbps
Certifications: CE, FCC, IC
Operating Temperature: -25 to 55°C (-13 to 131° F)
Operating Humidity: 5 to 95% Non-Condensing
Console Port: RS-232
Ethernet Ports: (24) 10/100/1000 Ethernet Ports, (2) SFP Ports
Passive PoE Configured Per Port via UI:
24V .75A pins 4,5(+) 7,8(-)
48V .75A pins 4,5(+) 7,8(-)
24VH 1.5A pins 1,2,4,5(+) 3,6,7,8(-)
48VH 1.5A pins 1,2,4,5(+) 3,6,7,8(-)
PoE Out Voltage Range: 48-50 VDC / 22-24 VDC
Passive PoE Current Sensors Per Port: YES
ESD Rating: 24 kV Air / 24 kV Contact
Manufactured and Assembled in North America
Standard Desktop / Wall mount
Optional 19” rack mount kit / Din Rail kit
Dimensons: 343 mm x 44 mm x 248 mm
Operating temperature -25 to 55°C (-13 to 131° F)
Serial console port
Passive PoE current sensors on each port